• Thermex® and/or VT-Therm®
    • Temperature indexes up to 240°C for electrical and magnet coils, transformers, motors, small industrial and wind turbine generators.
  • Thermibond®
    • Self-bonding wires that enable the motor or generator manufacturer to avoid using impregnation varnishes and thus to reduce manufacturing time cycles.

 

  • Copper
    • cross section range:  from 1.50mm² up to 100 mm², subject to thickness and width ratio.
  • Aluminium
    • cross section range: from 10mm² up to 100mm². The lower range is still going to be extended.

 

Advantages:

  • Different types of enamel with very good mechanical strength and bonding properties
  • Very consistent quality and dimensional tolerances per industry standard
  • Wide range of dimensions (very small to very large flatwire cross sections)

roun-d-wires

Technical Data Sheets:

33.C.F.0001 rev 231003SJ_CU_FLAT_Thermex_220

33.C.F.0002 rev 231003SJ_CU_FLAT_Thermex_220_G3

33.C.F.0003 rev 231003SJ_CU_FLAT_Thermibond_TS

33.C.F.0004 rev 231003SJ_CU_FLAT_Thermex_240

33.A.F.0001 rev 231003SJ_ALU_FLAT_Thermex_220

33.A.F.0002 rev 231003SJ_ALU_FLAT_Thermibond_TS

  • Silix®: glass yarn covered and varnish impregnated 
  • Daglas: thermally fused yarn combination of glass and polyester fibers, available both unvarnished and varnished.
  • VTV: combination of mixed glass /polyester fibers and impregnated glass yarn.
  • VS: yarn covered with outstanding thermal and mechanical properties, based on polyamide-imide or polyimide enamel for the conductor insula-
    tion and the covering impregnation.

 

Our yarn covered wires are ideal for applications where the wire insulation requires
improved mechanical properties, for example in:

  • rotor and stator windings
    • electrical motors (low- and high-voltage)
    • traction motors
    • wind turbine generators
  • conductor strands or Roebel bars
    • large power generators (hydro, turbo)

 

THE ADVANTAGES:

  • Wires with improved mechanical strength
  • High-performance yarns and impregnation varnishes
  • Wide range of insulation builds possible: standard, very thin or reinforced
  • Own means of production for a broad range of round and flat enamelled wires

 

roun-d-wires


Technical Data Sheets:

34.C.F.0001 rev 231003SJ_CU_FLAT_Daglas

34.C.F.0002 rev 231003SJ_CU_FLAT_Enamel_Daglas

34.C.F.0003 rev 240118_AEH_CU_FLAT_Silix

34.C.F.0004 rev 231003SJ_CU_FLAT_Enamel_Silix

34.C.F.0005 rev 231003SJ_CU_FLAT_TX 220_G1_1_ Daglas

34.C.F.0006 rev 231003SJ_CU_FLAT-VTV

34.C.F.0007 rev 231003SJ_CU_FLAT_Enamel_VTV

34.C.F.0008 rev 231003SJ_CU_FLAT_VS_220

34.C.F.0009 rev 231003SJ_CU_FLAT_VS_220_VF

34.C.F.0010 rev 231003SJ_CU_FLAT_VS_220 Renf_

34.C.F.0011 rev 231003SJ_CU_FLAT_VS_240

34.C.F.0012 rev 231003SJ_CU_FLAT_VS_240 VF

34.C.F.0013 rev 231003SJ_CU_FLAT_VS_240 RENF

34.C.F.0014 rev 231003SJ_CU_FLAT_VS_240 ER

34.C.F.0015 rev 231003SJ__CU_FLAT_ 2FO_100_GL_300

34.C.R.0001 rev 231003SJ_CU_ROUND_Daglas

34.C.R.0002 rev 231003SJ_CU_ROUND_Enamel_Daglas

34.C.R.0003 rev 231003SJ_CU_ROUND_Silix

34.C.R.0004 rev 231003SJ_CU_ROUND_Enamel_Silix

34.C.R.0005 rev 231003SJ_CU_ROUND_VS_240 EF

34.C.R.0006 rev 231003SJ_CU_ROUND_ FO_150_GL_300

34.NC.R.0001 rev 231003SJ_CUNi_ROUND_ Nickel_ 2_Silix_ VSI

34.A.F.0001 rev 231003SJ_ALU_FLAT_Enamel_Daglas

34.A.F.0002 rev 231003SJ_ALU_FLAT_Enamel_Silix

 

 

 

 

See catalogue:

bare-aluminum-conductor

bobina-alu

UNE EN 60228

 

NOMINAL SECTION COMPOSITION DIAMETER (mm) RESISTANCE WEIGHT

APPROX.

(Ω/Km)  (Kg/Km)
6 7×1,05 3,02 3,080 54
10 7×1,34 4,15 1,830 90
16 7×1,70 5,10 1,150 144
25 7×2,13 6,50 0,727 225
35 7×2,50 7,50 0,524 308
50 7×2,94 9,00 0,387 420
19×1,77 9,00 415
70 19×2,13 10,90 0,268 600
95 19×2,62 11,40 0,193 820
19×2,52 12,90 830
120 19×2,95 13,00 0,153 1060
37×2,05 14,50 1070
150 19×3,24 14,40 0,123 1290
37×2,21 16,20 1290
185 37×2,50 18,00 0,099 1650
240 61×2,25 20,60 0,075 2190
300 61×2,52 22,70 0,060 2650
400 61×2,82 26,00 0,047 3395
500 61×3,20 29,20 0,037 4340

 

 

WITH(mm) THICKNESS(mm) LENGHT(mm)
10 5 5000
15 5 5000
20 5 5000
25 3 5000
25 5 5000
30 3 5000
30 5 5000
40 5 5000
50 5 5000
50 6 5000
60 5 5000
80 5 5000
100 5 5000
120 5 5000
20 10 5000
30 10 5000
40 10 5000
50 10 5000
60 10 5000
80 10 5000
100 10 4000
120 10 5000
160 10 5000
50 15 5000

 

Material :
-Copper
-Aluminum

Sections: 
-Flat wire:  from 10×2 to 150x15mm
-Round: from 6 to 20mm
-Cable: from 6 to 300mm²

Stator coils up to 6,6 kV with VPI or Resin Rich insulation according to your needs.

Our capabilities :
– Minimum length of straight portion : 230 mm
– Maximum length of straight portion : 1500 mm
– Maximum distance between straights portions: 700 mm
– Maximum cross section: 20×40 mm
– Angle: 0 to 120 °

 

Bar with or without insulation

-Section : from 5×1 to 35x12mm

-Length : from 300 to 6000mm

Shaped Rotor Bars:

-Width: from 10 to 35mm
-Thickness: from 2 to 12mm

-Length of straight part : from 450 to 1880 mm

-Length of end-winding:  from 145 to 450 mm

 

 


Highlighted Products

CTC
Stranded and solid wires
POLYIMIDE
vidrio glassGLASS YARN COVERED